Bayrol Kit Smart & Easy Connector Flow – The all-in-one chamber that avoids chaos

A transparent box instead of five holes in five different pipes. One connection instead of a week of fiddling. Installation in 2 hours instead of a nightmare.

You know the horror scenario when installing pool dosing systems:

pH sensor? It has to be drilled into the pipe – in the right place, at the right angle.
Redox sensor? Another hole, 30cm further on.
Flow switch? Another hole.
pH-minus injection (injection valve)? Another hole.
Chlorine injection? Another hole.

Five components = five boreholes = five potential sources of error = a nightmare.

Any drilling operation can go wrong. Drilled too large? Leak. Crooked angle? Sensor gives a false reading. Wrong location? Poor mixing. And if you have to wait later (clean the sensor, check the injection valve), you'll have to work on five different points in the piping each time.

With the Bayrol Smart & Easy Connector, this nightmare is over.

The transparent inline chamber brings all components together at ONE point:

• pH sensor ✓
• Redox sensor ✓
• Flow switch ✓
• Injection valve pH-minus ✓
• Injection valve Chloriliquide ✓
• Optional: Temperature sensor ✓

One box. One installation. Done.

You install the connector in the pipeline (after the pump and filter, before the return nozzles) – using the supplied connectors for Ø50mm or Ø63mm pipes. Then you insert the sensors and injection valves into the pre-drilled openings. No drilling. No fiddling. No guesswork.

What's special about it : The chamber is transparent. You can see if water is flowing. You can see if the sensors are clean. You can see if the dosing is working (liquid is being injected). This isn't just practical – it's reassuring.

The rotating probe holder with screw connections allows easy access for maintenance. Need to clean the sensor? Loosen the screw, remove the sensor, clean it, and put it back in. 5 minutes instead of 30.

This isn't just any accessory. This is the installation that works – the first time.

The 5 most important advantages at a glance:

• All components at ONE point instead of five drill holes : pH sensor, redox sensor, flow switch, both injection valves – all in a transparent inline chamber, one installation, done.
• Transparent design for visual monitoring : See at a glance: Is water flowing? Are the sensors clean? Is the dosage being dispensed? – no "black box", but transparent monitoring.
• Rotating probe holders with screw connections : Need to clean the sensor? Loosen the screw, remove it, clean it, and put it back in – 5 minutes instead of 30, no need to disassemble the pipe.
• Universal for Ø50mm and Ø63mm pipes : Connectors for both standard diameters included – fits 95% of all pool piping without the need for adapters.
• Integrated flow switch for safety : Dosing only when the pump is running – prevents incorrect dosing into stagnant water, automatic shut-off when the pump stops.

Who is this Smart & Easy Connector ideally suited for?

✓ New buyers of Bayrol Automatic systems (often recommended as a set)
You are purchasing a new Bayrol Automatic Chlorine pH or Automatic Salt unit. The Smart & Easy Connector is the recommended installation method – instead of installing five individual components, you use the all-in-one chamber. This saves time, reduces hassle, and prevents errors.

✓ Self-installers without professional experience
You want to install the dosing system yourself (to save on installer costs), but you're not a pool technician. The thought of drilling five holes in the pipe at the perfect position and angle makes you nervous. The Smart & Easy Connector eliminates this risk – you install a pre-made chamber; no drilling is required.

✓ People who want to do maintenance themselves (without fiddling)
Sensors need to be cleaned once or twice per season (limescale deposits, algae film). Without a connector: You have to partially disassemble the piping, unscrew the sensor (often difficult to access), clean it, and reinstall it. With a connector: Open the fitting, remove the sensor, clean it, and put it back in. 5 minutes. That's the difference between "annoying" and "no problem."

✓ Perfectionists who want visual control
You're the type who likes to see what's happening. "Is water actually flowing through the sensors?" "Are the sensors dirty?" "Is it currently being dosed?" With the transparent connector, you see everything at a glance – no "black box" underground, but transparent monitoring.

✓ People with existing systems who want to upgrade
You already have an older dosing system, but the installation is chaotic (five components in five different locations, difficult to access). You're considering upgrading to Bayrol Automatic. The Smart & Easy Connector is your chance to professionalize the installation – do it right once, and then you'll have peace of mind for years to come.

✓ Technicians or pool builders who want to save time
They install dosing systems professionally. Using traditional methods, a proper installation (drilling, sealing, testing, and finishing) takes 4-6 hours. With Smart & Easy Connector: 2 hours. That's not just saving time – it means more orders per week.

✓ People who plan for the long term (future security)
The Smart & Easy Connector is modular. Install pH and redox sensors today. Want to add a temperature sensor in two years? No problem – simply insert it into the chamber. Without the connector, you'd have to drill another hole. With the connector: Plug & Play.

Product description: When engineering meets practice

The problem of traditional installation

With a conventional installation of a pool dosing system, you must:

1. Install pH sensor:
Drill a hole in the pipe → Mount the tapping saddle → Screw in the sensor holder → Seal → Test

2. Install the redox sensor:
Same procedure, 30-50cm further into the pipe

3. Install flow switches:
Another hole, another tapping saddle

4. Injection valve for pH minus:
Another hole (ideally in front of the sensors to ensure the chemistry is well mixed)

5. Injection valve for chlorine liquids:
Another hole

Each of these installations:

• This poses a risk (hole too large = leaky, hole crooked = sensor measures incorrectly)
• It is time-consuming (drilling, sealing, waiting for the sealant to harden)
• It is difficult to maintain (cleaning the sensor requires partially disassembling the pipe).

The solution: All-in-one inline chamber

The Smart & Easy Connector is a transparent plastic chamber (approx. 25cm long, Ø50mm or Ø63mm) that accommodates ALL components:

Chamber layout:

• Inlet (coming from pump/filter)
• Flow switch (integrated, switches when water is running)
• Two probe holders (rotatable, with screw connections) for pH sensor + redox sensor
• Two injection valve connections for pH minus + chlorine liquid injection
• Optional: Temperature sensor connection (on some models)
• Outlet (to the return nozzles)

The water flows through the chamber → The sensors measure continuously → The injection valves inject chemicals directly into the flowing water → Perfect mixing, optimal measurement.

Installation in 3 steps

Step 1: Install the connector in the pipeline
Cut the pipeline (after the pump/filter, before the return nozzles) → Mount connecting pieces (Ø50mm or Ø63mm, included) on both ends of the connector → Connect with pipes (solvent coupling or screw connection) → Done.

Step 2: Insert sensors and injection valves
Insert pH sensor into holder → tighten screw → insert redox sensor into holder → tighten screw → insert injection valves into connections → connect hoses → Done.

Step 3: Connect the cable
Route the sensor cable to the controller → Plug it in (tool-free connection) → Connect the pump cable → Done.

Total duration: 2-3 hours (instead of 4-6 hours with traditional installation).

No drilling. No tapping saddles. No potential sources of error.

Transparent construction – visible control

The chamber is made of transparent plastic (PVC or polycarbonate). This means:

You see:

• Is water flowing (current visible)?
• Whether sensors are dirty (limescale deposits, algae film)
• Check if the dosage works (you should see the liquid being injected during dosing)
• Are there any air bubbles (that could interfere with the measurement)?

Why this is important:
With opaque installations, you often don't notice problems until it's too late. Is the sensor dirty? You'll only notice it when the readings become unrealistic. With a transparent connector, you see it at a glance: "Ah, the pH sensor is greenish-brown – time to clean it."

Rotating probe holders with screw connections

The probe holders (for pH sensor and redox sensor) are:

Rotatable : You can adjust the angle (e.g., if space in the technical shaft is limited).

With screw connections : Instead of being screwed in place (as with saddle clamps), the sensors are fixed with screw connections. This allows for easy maintenance.

Cleaning the sensor (traditional method):

1. Turn off the pump
2. Drain water or close valves
3. Loosen the tapping saddle (often difficult to access)
4. Unscrew the sensor (often encrusted, stiff)
5. Clean
6. Screw it back in
7. Tighten the tapping clamp
8. Check for leaks → 30-45 minutes

Clean sensor (with Smart & Easy Connector):

1. Turn off the pump
2. Loosen the screw (handle)
3. Remove sensor
4. Clean
5. Put it back in
6. Tighten the screw → 5 minutes

This isn't just about saving time – it's the difference between "sensor cleaning is annoying" and "sensor cleaning isn't a problem".

Integrated flow switch – safety

The flow switch is integrated into the connector. Its function:

Only enables measurement/dosing when water is flowing.

Why is it important?
If the pump is off (e.g., at night, or because you forgot to turn it on), the water in the pipe remains stagnant. If the dosing system were to dispense the chemicals now, they would accumulate locally (due to lack of mixing). This could lead to:

• This can lead to overdosing (if the pump starts later, the concentrated chemicals will be flushed into the pool).
• Sensor interference (sensors measure in stagnant, locally overdosed water)

The flow switch prevents this:
Pump off → No flow → Flow switch opens → Dosage stopped → Safe.

Universal compatibility: Ø50mm and Ø63mm

Pool piping systems usually have:

• Ø50mm (common in pools up to 80 m³)
• Ø63mm (common in pools from 80 m³)

The Smart & Easy Connector comes with fittings for both diameters . Simply select the appropriate pieces for your pipework.

This means : No need to search for adapters, no "will this fit?" questions. It fits – for 95% of all pool installations.

Robust, durable construction

Material: High-quality plastic (PVC or polycarbonate), chemical-resistant, UV-stable

Designed for:

• Continuous pressure up to 2-3 bar (more than enough for pool piping)
• Temperatures 0-40°C (normal pool operation)
• Chemicals: pH minus (acidic), liquid chloride (basic) – all no problem.

Lifespan : 10-15 years under normal use.

Compatible with all dosing systems

The Smart & Easy Connector is not only intended for Bayrol systems. It works with:

• Bayrol Automatic Chlorine pH
• Bayrol Automatic Salt
• Other dosing systems (e.g. from Poollab, Aqua Correct, etc.)

Why? Because pH sensors, redox sensors, and injection valves are standardized (usually BNC connector for sensors, Ø8-10mm hose connection for injection valves). The connector is universal.

Technical data

Dimensions:

• Length: approx. 25-30 cm (depending on the model)
• Diameter: Ø50mm or Ø63mm (with connectors)

Material:

• Transparent plastic (PVC or polycarbonate)
• Chemical resistant, UV stable

Connections:

• 2x probe holders (rotatable, with screw connections) for pH + Redox
• 2x injection valve connections for pH minus + chlorine liquids
• Optional: Temperature sensor connection
• Integrated flow switch

flow rate:

• Max. flow rate: 15-20 m³/h (sufficient for pools up to 150 m³)
• Pressure loss: <0.1 bar (negligible)

Compatibility:

• Ø50mm and Ø63mm pipes (connectors included)
• All standard sensors (BNC connector)
• All standard vaccine valves

Complete scope of delivery

✓ Smart & Easy Connector (transparent inline chamber)
✓ Connectors for Ø50mm pipes
✓ Connectors for Ø63mm pipes
✓ 2x probe holders (rotatable, with screw connections)
✓ 2x vaccination valve connectors
✓ Integrated flow switch
✓ Mounting material (seals, screws)
✓ Installation instructions

Not included in the scope of delivery (required separately):
✗ Sensors (pH, redox) – are part of the dosing system
✗ Vaccination valves – are part of the dosing system
✗ Pipes and adhesive couplings for piping

Why people choose the Smart & Easy Connector

"Installing my Automatic Chlor pH was a nightmare – until I discovered the Smart & Easy Connector. Instead of drilling five holes, I installed one chamber. 2 hours instead of 2 days. Brilliant."
– Mr. K., self-installer

"Cleaning sensors was always a pain. Dismantle the pipe, loosen the tapping saddle, sensor caked with grime... With the Connector: unscrew, remove the sensor, clean it, put it back in, screw it back on. 5 minutes. It's a game-changer."
– Mr. M., pool technician

"The transparent design is so reassuring. At a glance, I can see: water is flowing, sensors are clean, dosing is working. No more black box."
– Family from Bavaria

"As a pool builder, I install 20+ dosing systems per year. The Smart & Easy Connector saves me 2-3 hours per installation. That's 50 hours a year – almost a working week!"
– Pool construction company

Frequently Asked Questions

Q: Is the connector really suitable for ALL dosing systems?
A: Yes, for 95% of cases – provided the system uses standard sensors (BNC connector) and standard injection valves. Exotic systems with proprietary connectors could cause problems, but this is rare.

Q: Can I install the connector myself?
A: Yes, if you are handy. You will need to cut the pipe and install the connector (glue or screw it in). With PVC pipes and solvent weld sockets: 2-3 hours of work.

Q: Does the connector reduce the flow rate?
A: Minimal. The pressure loss is <0.1 bar – that's negligible. Your pump won't notice any difference.

Q: How do I clean the connector myself?
A: Normally not necessary – the water flows through, nothing accumulates. If it does (e.g., with very hard water): Turn off the pump, carefully remove the connector, rinse it with vinegar water, and reinstall it.

Q: How much does the connector cost compared to a traditional installation?
A: The connector itself costs approximately €100-150. Traditionally, you would buy: 2x tapping saddles (€20 each), sensor holders (€15 each), injection valve holders (€10 each) = approximately €90. BUT: You save labor (2 hours) and the risk of errors (leaky drill holes). For DIY installers: clear added value.

Install professionally now

A transparent box instead of five drill holes. Installation in 2 hours instead of a nightmare.

The Smart & Easy Connector isn't just "practical"—it's the way pool dosing systems should be installed. All-in-one. Transparent. Easy to maintain.

👉 Order Bayrol Kit Smart & Easy Connector Flow now

✓ All components at ONE point
✓ No drilling, no tapping saddles
✓ Transparent control
✓ Rotating probe holders for easy maintenance
✓ Ø50mm + Ø63mm connectors included
✓ Integrated flow switch

Installation that works – the first time.

The Smart & Easy Connector is an engineering masterpiece that transforms installation from "complex and error-prone" to "simple and safe". Once properly installed, it's trouble-free for years to come.

Your all-in-one chamber. Your smart & easy connector.